Download Quick Start Guide Clickดูแนวทางการใช้งาน ClickIntroduction:
This Holybro SiK Telemetry Radio is a small, light and inexpensive open source radio platform that typically allows ranges of better than 300m “out of the box” (the range can be extended to several kilometres with the use of a patch antenna on the ground).
This radio is plug-n-play all Pixhawk Standard and other Flight Controller, providing the easiest ways to setup a telemetry connection between your Autopilot and a ground station. It uses open source firmware which has been specially designed to work well with MAVLink packets and to be integrated with the Mission Planner, Ardupilot, QGroundControl, PX4 Autopilot.
The radios can be either 915Mhz or 433Mhz and you should purchase the model which is appropriate for your country/region.
Note:
This radio does not support firmware upload via Mission Planner 1.3.75 or older. Please use Mission Planner 1.3.76 (QGroundControl v4.2.0 ) or newer if firmware upload is needed.
The current batch of Sik Telemtry Radio uses the SI1060 chip (previously SI1000) shipped with updated firmware. Older firmware without SI1060 chip support is not compatible.
Features:
- Open-source SIK firmware
- Plug-n-play for Pixhawk Standard Flight Controller
- Easiest way to connect your Autopilot and Ground Station
- Interchangeable air and ground radio
- Micro-USB port (Type-C Adapter Cable Included)
- 6-position JST-GH connector
Specification:
- 100 mW maximum output power (adjustable) -117 dBm receive sensitivity
- RP-SMA connector
- 2-way full-duplex communication through adaptive TDM UART interface
- Transparent serial link
- MAVLink protocol framing
- Frequency Hopping Spread Spectrum (FHSS) Configurable duty cycle
- Error correction corrects up to 25% of bit errors Open-source SIK firmware
- Configurable through Mission Planner & APM Planner
- FT230X is a USB to BASIC UART IC
Dimension:
- 28 x 53 x 10.7mm (without antenna)
Electrical Data:
- Supply voltage: 5V DC (from USB or JST-GH)
- Transmit current: 100 mA at 20dBm
- Receive current: 25 mA
- Serial interface: 3.3 V UART
The radios have 2 status LEDs, one red and one green.The meanings of the different LED states are:
- Green LED blinking - searching for another radio
- Green LED solid - link is established with another radio
- Red LED flashing - transmitting data
- Red LED solid - in firmware update mode
Connecting to Pixhawk Standard Flight Controller
Use the 6 pin JST-GH connector that come with the radio to connect the radio to your flight controller's “Telem 1” (“Telem 2” can also be used but the default recommendation is “Telem1”).
Connecting to a PC or Ground Station
Connecting the radio to your Windows PC or Ground Station is as simple as connecting the micro/type-C USB cable (both included with the radio) to your PC/Ground Station.
The necessary drivers should be installed automatically and the radio will appear as a new “USB Serial Port” in the Windows Device Manager under Ports (COM & LPT). The Mission Planner’s COM Port selection drop-down should also contain the same new COM port.
Package Included:
- Radio modules with antennas x 2
- Micro-USB to USB-A cable x 1
- Micro-USB to Micro-USB OTG adapter cable x 1
- Micro USB to Type C Adapter x 1
- JST-GH-6P to JST-GH-6P cable x 1 (for Pixhawk Standard FC)
- JST-GH-6P to Molex DF13 6P x 1 (for Pix32, Pixhawk 2.4.6, etc.)