ESP32-S2-Saola-1M Development Board (แท้จาก DFRobot)

ESP32-S2-Saola-1M Development Board (แท้จาก DFRobot)
ESP32-S2-Saola-1M Development Board (แท้จาก DFRobot)ESP32-S2-Saola-1M Development Board (แท้จาก DFRobot)ESP32-S2-Saola-1M Development Board (แท้จาก DFRobot)ESP32-S2-Saola-1M Development Board (แท้จาก DFRobot)ESP32-S2-Saola-1M Development Board (แท้จาก DFRobot)ESP32-S2-Saola-1M Development Board (แท้จาก DFRobot)
รหัสสินค้า BA00192
หมวดหมู่ WiFi ESP32-S2
ราคา 895.00 บาท
สถานะสินค้า พร้อมส่ง
จำนวน
ชิ้น
หยิบลงตะกร้า
หนังสือรับรองบริษัท
บุ๊คแบ๊งค์
คุ้มครองโดย LnwPay
ดูการใช้งานอย่างละเอียดได้ที่ Click

Introduction
ESP32-S2-Saola-1 is a small-sized ESP32-S2-based development board. Most of the I/O pins are broken out to the pin headers on both sides for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-S2-Saola-1 on a breadboard.

ESP32-S2-Saola-1 is equipped with ESP32-S2-WROOM module, a powerful and generic Wi-Fi MCU module that has a rich set of peripherals. It’s an ideal choice for a wide variety of application scenarios like wearable electronics and smart home. The board has PCB onboard antenna, and 4MB SPI flash.

Description of Components

 

 

ESP32-S2-Saola-1M Development Board

Key Component

Description

ESP32-S2-WROVER

ESP32-S2-WROVER is a powerful, generic Wi-Fi MCU module that integrates ESP32-S2. It has a PCB antenna, a 4 MB external SPI flash and an additional 2 MB PSRAM.

I/O Connector

All available GPIO pins (except for the SPI bus for flash and PSRAM) are broken out to the pin headers on the board. Users can program ESP32-S2 chip to enable multiple functions such as SPI, I2S, UART, I2C, touch sensors, PWM etc.

USB to UART Bridge

Single USB-UART bridge chip provides transfer rates up to 3 Mbps.

Boot Button

Download button. Holding down Boot and then pressing Reset initiates Firmware Download mode for downloading firmware through the serial port.

Reset Button

Reset button.

3.3 V Power On LED

Turns on when the USB power is connected to the board.

Micro-USB Port

USB interface. Power supply for the board as well as the communication interface between a computer and the ESP32-S2 chip.

RGB LED

Addressable RGB LED (WS2812), driven by GPIO18.

 

 

Block Diagram

 

ESP32-S2-Saola-1M Development Board

SPECIFICATION

  •  
  • ESP32-S2 chip, Xtensa single-core 32-bit LX7 Microcontroller
  • 128 KB ROM
  • 320 KB SRAM
  • 16 KB RTC SRAM
  • 40 MHz crystal oscillator integrated
  • 4 MB SPI flash
  • Operating/Supply Voltage: 3.0 ~ 3.6 V
  • Recommended Operating Temperature: –40 ~ 85 °C

DOCUMENTS

SHIPPING LIST
  • ESP32-S2-Saola-1M Development Board x1







วิธีการชำระเงิน

ชำระเงินค่าสินค้าโดยการโอนเงินเข้าบัญชีธนาคาร KBANK, SCB, BBL,TMB

กรุณาเก็บหลักฐานการโอนเงินของท่านไว้เพื่อแจ้งการชำระเงินด้วยค่ะ

 

ท่านสามารถแจ้งการชำระเงินผ่านระบบอัตโนมัติได้โดย Click Link ข้างล่างค่ะ

https://www.arduitronics.com/informpayment

 

บมจ. ธนาคารกสิกรไทย สาขาเซ็นทรัล แจ้งวัฒนะ ออมทรัพย์
ธนาคารไทยพาณิชย์ จำกัด (มหาชน) สาขาเซ็นทรัล แจ้งวัฒนะ ออมทรัพย์
ธนาคารกรุงเทพ จำกัด (มหาชน) สาขาเซนทรัล พระราม 3 สะสมทรัพย์
ธนาคารทหารไทยธนชาต จำกัด (มหาชน) สาขาเซนทรัล พระราม 3 กระแสรายวัน

เพิ่มเพื่อน

@rfm0967y

ติดต่อสอบถาม

เพิ่มเพื่อน

CATEGORY

Sensors / Modules [1695]

CONTACT US

มือถือ 0887823467 แฟกซ์ 02-0153201

Join เป็นสมาชิกร้านค้า

ร้านArduitronics
ร้านArduitronics
/www.arduitronics.com/
Join เป็นสมาชิกร้าน
2118
สมัครสมาชิกร้านนี้ เพื่อรับสิทธิพิเศษ

STATISTICS

หน้าที่เข้าชม15,375,197 ครั้ง
ผู้ชมทั้งหมด5,878,275 ครั้ง
เปิดร้าน21 พ.ค. 2556
ร้านค้าอัพเดท5 ก.ย. 2568

MEMBER

พูดคุย-สอบถาม