SparkFun Pressure Sensor Breakout - MS5803-14BA (ของแท้จาก Sparkfun, USA)

SparkFun Pressure Sensor Breakout - MS5803-14BA (ของแท้จาก Sparkfun, USA)
SparkFun Pressure Sensor Breakout - MS5803-14BA (ของแท้จาก Sparkfun, USA)SparkFun Pressure Sensor Breakout - MS5803-14BA (ของแท้จาก Sparkfun, USA)SparkFun Pressure Sensor Breakout - MS5803-14BA (ของแท้จาก Sparkfun, USA)SparkFun Pressure Sensor Breakout - MS5803-14BA (ของแท้จาก Sparkfun, USA)SparkFun Pressure Sensor Breakout - MS5803-14BA (ของแท้จาก Sparkfun, USA)
รหัสสินค้า AS00514
หมวดหมู่ วัดสภาพแวดล้อมและแก๊ส Environmental / Gas
ราคา 2,685.00 บาท
สถานะสินค้า พร้อมส่ง
จำนวน
ชิ้น
หยิบลงตะกร้า
หนังสือรับรองบริษัท
บุ๊คแบ๊งค์
คุ้มครองโดย LnwPay
Description:
This is the MS5803-14BA Pressure Sensor Breakout, a high resolution pressure sensor with both an I2C and SPI interface. This MEMS pressure sensor measures the absolute pressure of the fluid around it which includes air, water, and anything else that acts like a viscous fluid. Depending on how you interpret the data, you can determine altitude, water depth, or any other tasks that require an accurate pressure reading. What makes the MS5803-14BA unique is the the gel membrane and antimagnetic stainless steel cap that protects against 30 bar water pressure.
We have broken out all the pins you need including GND and 3.3V for power, SDA/SDI and SCL/SCLK for an I2C interface and SD0, AD/CS, and PS for a SPI interface. The MS5803-14BA Breakout offers a resolution range of 1 / 0.6 / 0.4 / 0.3 / 0.2 mbar. Be aware that to switch between I2C and SPI interfaces a little bit of soldering between solder pads will be required, check the hookup guide below for more information.
Heads up! While the IC is capable of outputting data via I2C and SPI, the Arduino Library and example was only written to output via I2C! You'll need to modify the jumpers on the board for SPI mode by removing solder from the pull-up resistors jumper pads and close the other two jumpers. Additionally, you will need to write a library to communicate with the MS5803 in SPI mode if you plan on using this with Arduino.



Features:
  • Operating Voltage - 1.8 to 3.6 V
  • Peak Supply Current - 1.4 mA
  • Operating Range - 0 to 14 bar
  • Resolution - 1 / 0.6 / 0.4 / 0.3 / 0.2 mbar
  • I2C and SPI Interface
  • Gel Protected
Documents:

วิธีการชำระเงิน

ชำระเงินค่าสินค้าโดยการโอนเงินเข้าบัญชีธนาคาร KBANK, SCB, BBL,TMB

กรุณาเก็บหลักฐานการโอนเงินของท่านไว้เพื่อแจ้งการชำระเงินด้วยค่ะ

 

ท่านสามารถแจ้งการชำระเงินผ่านระบบอัตโนมัติได้โดย Click Link ข้างล่างค่ะ

https://www.arduitronics.com/informpayment

 

บมจ. ธนาคารกสิกรไทย สาขาเซ็นทรัล แจ้งวัฒนะ ออมทรัพย์
ธนาคารไทยพาณิชย์ จำกัด (มหาชน) สาขาเซ็นทรัล แจ้งวัฒนะ ออมทรัพย์
ธนาคารกรุงเทพ จำกัด (มหาชน) สาขาเซนทรัล พระราม 3 สะสมทรัพย์
ธนาคารทหารไทยธนชาต จำกัด (มหาชน) สาขาเซนทรัล พระราม 3 กระแสรายวัน

เพิ่มเพื่อน

@rfm0967y

ติดต่อสอบถาม

เพิ่มเพื่อน

CATEGORY

Sensors / Modules [1702]

CONTACT US

มือถือ 0887823467 แฟกซ์ 02-0153201

Join เป็นสมาชิกร้านค้า

ร้านArduitronics
ร้านArduitronics
/www.arduitronics.com/
Join เป็นสมาชิกร้าน
2129
สมัครสมาชิกร้านนี้ เพื่อรับสิทธิพิเศษ

STATISTICS

หน้าที่เข้าชม15,393,873 ครั้ง
ผู้ชมทั้งหมด5,896,951 ครั้ง
เปิดร้าน21 พ.ค. 2556
ร้านค้าอัพเดท17 ก.ย. 2568

MEMBER

พูดคุย-สอบถาม